Wednesday 12th June

PERIOD OF WEBSHOP CLOSURE  TO FACILITATE REORGANISATION OF STOCK 

REOPENING MONDAY 1st JULY 

ORDERS RECEIVED TO DATE IN PROCESS . 

NO PRICING APPEARS DURING THIS PERIOD

WE THANK YOU FOR YOUR PATIENCE AT THIS TIME

 

 

 

 

 

 

 

 

 

CLEARANCE & SPECIAL OFFER ITEMS

SPECIAL OFFER rates will ***STRICTLY*** ONLY BE HONOURED for orders submitted online....any items phoned through will be priced at normal, non discounted rates.

Beaded Hunting Crop Collar

Special OfferBeaded Hunting Crop Collar

Currently on special offer!



Gents 24/22mm taper, 38mm long

Ladies (Short) 20/19mm taper, 32mm long

Ladies (Long) 19/17mm taper, 38mm long

Childs 16/15mm taper, 32mm long

All diameters are internal.

We can engrave these with your chosen inscriptions / artwork for as little as £2.00 per item. Please enquire if this is required.

LONG NOSE MARKET HANDLE

Special OfferLONG NOSE MARKET HANDLE

Currently on special offer!


***LIGHT & MEDIUM WEIGHT HANDLES ON SALE***
Same as the shaped Standard market Handle but made from a larger, heavier horn giving a long "turnable" nose. Will make up into a nose out Market Handle / Crook with a little heating and shaping.
Some figured pieces ( occasionally!!! ) available showing greys and white up the heel and over the crown.
Plumb and balanced in proportion.
Heavier weights shank to 26mm+
Medium will typically shank to 23 - 25mm.
Lighter pieces available....suitable for ladies weight sticks ( typically 20/22mm on base).

Buffalo Horn - Knobstick handles

Special OfferBuffalo Horn - Knobstick handles

Currently on special offer!

Nicely balanced, solid water buffalo handles in traditional Victorian patterns.

"ROUND HANDLE" - shown left
"PRINCE OF WALES" HANDLE - shown right

Ideal for lighter weight shafts, especially walking stick heights and will fit at 21 - 23mm. Most show striking graining and some with grey / green streaks evident on polishing to finish. Both may also be carved.
The "Round" handle provides a very solid grip where support from the stick is required.
The "Prince of Wales" grip is ideal for a more slender shaft and is more a decorative than supportive handle in use.

Chestnut Twisters

Special OfferChestnut Twisters

Currently on special offer!

JUNE 2019 - ***FRESH STOCK NOW ON THE SHELF*** excellent selection of diameters, superb, even stock.

4'6" ( 137cm ) length and 23 - 26mm top diameter.

These are carefully selected " Premium" chestnut shanks, stripped, then expertly spiral grooved, by hand, on a machine, using first a broad "fingernail" faced cutter and then another identical cutter, the second cut being half the width of the first.
The resultant pattern is as close to a natural "vine" created grooving as it's possible to get.
The sticks are then flamed and lightly polished.
Very attractive, eye catching, dependable strong sticks.

151 RAPID TWO PART EPOXY

Special Offer151 RAPID TWO PART EPOXY

Currently on special offer!


Been a few supply issues with "151" of late, now resolved. Happy to say that it's back in stock, same packaging format as before and every bit as effective if not better.

Reinstated to long term Special Offer .......

Aluminium Oxide roll

Special OfferAluminium Oxide roll

Currently on special offer!


***CLEARANCE ITEMS***

25mm (1 inch ) wide cloth backed "Al Ox" roll in handy 10 metre lengths.

Will rip longways into tough narrow strips for "strapping".
Various grits.,
60 (coarse)
100 (general roughing down )
180 (fine shaping )
220 (pre polish )
320 (fine pre polish )

Plain Hunting Crop Collars

Special OfferPlain Hunting Crop Collars

Currently on special offer!



Gents 24/22mm taper, 38mm long

Ladies (Short) 20/19mm taper, 32mm long

Ladies (Long) 19/17mm taper, 38mm long

Childs 16/15mm taper, 32mm long

All diameters are internal.

We can engrave these with your chosen inscriptions / artwork for as little as £2.00 per item. Please enquire if this is required.

Hi Carbon Damascus bar - 1/8

Special OfferHi Carbon Damascus bar - 1/8

Currently on special offer!


***CLEARANCE ITEM***

Nominal lengths to 40" available.

1.5" width, 1/8" thickness

Hi carbon tool steel 01 & 1095 mix giving good tight Bird's Eye pattern.

Illustration shows surface of ground and acid treated bar before hardening.

Material will require basic hardening and tempering ahead of use.

Priced per linear inch....****MINIMUM ORDER 4 INCHES****

CHESTNUT

Special OfferCHESTNUT

Currently on special offer!



Seasoned, straightened....strong, nicely tapered, rich burgundy / chocolate coloured bark with interesting, regular figuring around the numerous, carefully dressed knots. Take a beautiful oiled finish.

All shanks in range 52" - 54"

PREMIUM - very best available, superbly straight and assured taper. Generally 23 - 26mm tops.

STANDARD - good everyday stick, well balanced and very well straightened. Generally 23 - 26mm top diameter

HEAVY - as standard but 27 - 30+mm tops.

WORKING - Often with slight bark blemishes which the experienced stickmaker will easily rectify - leaving an attractive, serviceable stick.

LIGHT WEIGHT - Tops are 22mm or less.

False Noses and Pigtail adapters

Special OfferFalse Noses and Pigtail adapters

Currently on special offer!

Which is which

False noses (see top in photo) enable a bench grinder to be adapted for use as a polishing machine. Strip the guards and stones off and secure the noses (sleeve on fitting - grub screw retention). When correctly fitted mop will rotate towards you in order that any "snatch" of workpiece from your grasp propels it towards the floor and not up into your face!!!!
Guarding upon adaptation is an important safety consideration!!!
Grinders will handle all of the mop sizes we sell - for larger diameter mops simply raise the grinder on a wooden block.

Pigtails (single - bottom in photo) enable use of mops with a veice secured electric drill. Best to have one pigtail per mop as they take a very very tight grip!! Fit most domestic chucks to 1/2"
False noses are **NEW** and unused but may have light layer of surface rust

Cow horn, Craft Grade

Special OfferCow horn, Craft Grade

Currently on special offer!



We source these horns in West Africa for a variety of reasons. Availability, size, versatility in application, but above all else, colour. Like all cow horns, they either have darker ( black ) or lighter ( varying shades of brown ). Whatever colour is present in the tip, it diffuses into streaked, lighter / cream and white colour as you move up the horn towards the broad, hollow end.
All horns are cored out, boil washed and hygenic - just as we receive them.
Typically they will be used for drinking horns, blowing horns, powder horns or cuttting down to yield a variety of plates / rounds / tips for use in making smaller items such as spoons, bangles, shoe horns and other items too numerous to mention.
If the colours look good "in the raw", then just wait until they are sanded and polished, when the material really comes alive with stark contrasting tones and depth of colour.
Please bear in mind that pretty much 100% of cow horns suffer from internal concentric splitting to a greater or lesser extent...a seperation of layers that is always present. This is not something that we can effectively select to avoid - it's always there, period. A little care will however get you around it and it need not necessarily be to the detriment of the worked article, especially once you have "the hang" of working with the material.
Categorised in three different length classes.,
18 - 24"
24 - 30"
30"+ ( up to 44" on occasion )
Call us to discuss individual selection tailored to your requirements or put some relevant comments in the field at the end of the ordering process please.

Buffalo Lyre handle

Special OfferBuffalo Lyre handle

Currently on special offer!

Shaped like a "Lyre" these pieces are widely popular and sought after, making most attractive thumbstick or stalking pole tops. Many with attractive veining visible in finished surface.



HAZEL

Special OfferHAZEL

Currently on special offer!

Hazel, overall, is the default choice for stickmaking. Strong, well tapered and with varied and attractive bark markings.

Premium Grade - The best of the batch, round, well figured, well tapered and no visible defects. 23 - 27mm tops. Other diameters ( please request on comments field ) subject to stock.


Standard Grade - Very little to set these apart from their Premium counterparts - nice bark, nice taper, typically a few more knots to add character. 23 - 27mm tops

Standard Grade, at present are very very close to premium all round, a few knots / cross sectional issues will set them apart.

Light weight - NO CURRENT STOCK

Heavier weight - Again , same as standard but weightier, being 27 - 32mm at the top

Working Grade - NO CURRENT STOCK

We will accomodate any special requests subject to stock. ( place in comments field at end of ordering process please)

Loose leaf

Special OfferLoose leaf

Currently on special offer!

Mixed grade fabric mop incorporating linen and cotton. All 1" working width and in the following diameters.....

3" - smallest - best for "inside lines" on handles

6" - handy "all rounder", perfectly satisfactory for lighter grinders where you do not wish to overstress the bearings.

8" - by far the most popular mop, it's 4 inch "reach" enables most handles to be polished to the centre mark, meaning that very few "nooks" are inaccessible!!!

10" - this 1/2" working width mop in fine and "floppy" in use and reaches (flexibly) a little further than the 8" if you are doing a lot of handles.

Market / Walker top / basic pattern

Special OfferMarket / Walker top / basic pattern

Currently on special offer!




**** SALE OF LIGHT & MEDIUM WEIGHT HANDLES***

In Black buffalo horn, often showing attractive white and grey veining.

Fully formed, plumb and "in line", but may be further "turned in" with the application of a little heat and clamping.
Heavier 26mm and over
Medium 23 - 26mm
Lighter weight 20 - 22mm

Bugle candle cup

Special OfferBugle candle cup

Currently on special offer!

Illustrated with the optional drip tray, these candle cups are manufactured with a "staybright" nickel plated finish. 47mm high and 41mm at their widest point (top)
Will accomodate a candle diameter of 22mm without trimming of candle base.
The narrowed base portion accomodates a 5mm pilot hole which may be used to secure the cup to whatever it is being fixed onto ( especially useful in securing to antler...the narrowed section may be sunk into the antler to assist in leveling the piece ) Self tapping screws or set screws with nuts ( not supplied) are best for securing the piece to it's chosen base.
114

Cow Horn Tips

Special OfferCow Horn Tips

Currently on special offer!

Well coloured, thick walled, substantial tips cut from bulk stock of "Craft Grade" horns. Broadly categorised as "dark" ( black and dark brown finish) and lighter ( light brown, cream and olive tones ). The tip colour will diffuse back into lighter cream and white colours as you move towards the broad end of the piece. Generously cut - usually 8" - 10" in length.
Note: ALL cow horns suffer from splits. Should minor splitting be evident in these horns, ,then for stickmaking, it is assumed that they will be shanked on the nose end and "capped off" or "domed" ( with resin ).
That said, no cracking present will be to the potential detriment of the finished piece.

Needle Rasp set

Special OfferNeedle Rasp set

Currently on special offer!

***CLEARANCE ITEM***

6 piece, super sharp, varied profiles, same grade of alloy as our Dreadnought file range.

Great for creating intricate detail in horn.

Supplied "carded" and with plastic handles pre fitted

Cabinet rasps

Special OfferCabinet rasps

Currently on special offer!



***CLEARANCE ITEMS***
The half round for rough preparatory work and the round for sharp and rapid removal of material in the formation of turned out noses / inside lines. 10 inch round is particularly sharp and supplied in 2nd cut format
***supplied "bare" - without handle***

Milenicut files

Special OfferMilenicut files

Currently on special offer!



***CLEARANCE ITEMS***
Similar to Dreadnought files but have an offset and cross notchedtooth pattern making them ideal for rapid removal of material whilst leaving an excellent smooth worked surface
***supplied "bare" - without handle***

Dreadnought File

Special OfferDreadnought File

Currently on special offer!



***CLEARANCE ITEMS***
Sometimes called "milled tooth" files. Made in specially hardened alloy steel and produced with a definite undercut to ensure that they remain "clog" free in use, these are, without doubt "the" files to work horn with.
***supplied "bare" - without handle***

Crimpable Cow Horn

Special OfferCrimpable Cow Horn

Currently on special offer!


Select pieces of "Craft Grade" cow horns - normally very "narrow" / "thin" individual horns which have particularly thick walls, normally lighter coloured pieces ( the ones that are narrow and "crimpable" usually have the best, lighter colours.....like "coloured" buffalo horn ).
These may be "crimped" using Hi Torq stainless steel jubilee clips ( often used for commercial vehicle exhaust systems ) or blocks / jigs ( like pipe crimping equipment ) designed for this type of job.
Cow horn is surprisingly soft and pliable when carefully heated ( hot air gun best ).

Only the most select of material offered for sale as this quality.

Ox Horn Hollows

Special OfferOx Horn Hollows

Currently on special offer!


These are cut from our "Craft Grade" material and are suited to making drinking cups / similar or for cutting to yield layered, variegated strips or small blocks of material for capping or general craft and jewellery work.
Good for bangles!!! Fantastic interesting and attractive colours. 10 - 16" random cut lengths, typically 3 - 5" internal diameter on broad end and 2 - 4" internal diameter on the narrow end.
We can offer good bulk discounts from huge current stock, export orders catered to with ease subject to required Customs paperwork at destination.
MINIMUM ORDER VALUE OF £20 APPLIES - MIXED or ALL IN HOLLOWS

8 inch VFA

Special Offer8 inch VFA

Currently on special offer!

4 lap Scotchbrite (VFA) mop, produces "satin" like surface effect when used gently on horn, saves a lot of time on sandpapering!!!

The COARSE mop is ideal for stripping back natural weathered surface on cow horns prior to polishing.

Both of these items when run on a polisher or grinder motor do a great , timesaving job, BUT have the ability to cause significant abrasive damage to your fingers / skin and also generate dust. Due care and appropriate protective clothing and dust extraction should be used!!!!

Thistle pattern candle cup

Special OfferThistle pattern candle cup

Currently on special offer!

Our best selling candle cup.
Illustrated with the optional drip tray, these candle cups are manufactured with a "staybright" nickel plated finish. 52mm high and 42mm at their widest point (top)
Will accomodate a candle diameter of 22mm without trimming of candle base.
The narrowed base portion accomodates a 5mm pilot hole which may be used to secure the cup to whatever it is being fixed onto ( especially useful in securing to antler...the narrowed section may be sunk into the antler to assist in leveling the piece ) Self tapping screws or set screws with nuts ( not supplied) are best for securing the piece to it's chosen base.

Bluebell Candle cup

Special Offer Bluebell Candle cup

Currently on special offer!

Illustrated with the optional drip tray, these candle cups are manufactured with a "staybright" nickel plated finish. 42mm high and 33mm at their widest point (top)
Will accomodate a candle diameter of 22mm without trimming of candle base.
The narrowed base portion accomodates a 5mm pilot hole which may be used to secure the cup to whatever it is being fixed onto ( especially useful in securing to antler...the narrowed section may be sunk into the antler to assist in leveling the piece ) Self tapping screws or set screws with nuts ( not supplied) are best for securing the piece to it's chosen base.
121

CAMSTAG ( SAMBAR STAG LOOKALIKE )

Special OfferCAMSTAG ( SAMBAR STAG LOOKALIKE )

Currently on special offer!


***CLEARANCE ITEM***

Excellent Camel bone Sambar Stag scale lookalike material, each piece unique and hand finished.
VERY AUTHENTIC
All material has been dyed by immersion in Potassium Permanganate solution, giving a very dark "Verona" brown colour, which, just like the real thing, will surface polish to remove a lot or a little dye depending on how hard you polish the surfaces, enabling the desired finished appearance to be achieved and admired.

Ordering How It Works...

The Highland Horn Online Shop is temporarily closed. We do not accept new orders during this period. We will be open again shortly. Apologies for any inconvenience caused.

Highland Horn Company Ltd, Taigh na Corrach, Knockmuir Brae, Avoch, Ross-Shire, Scotland IV9 8RD

Tel: +44 (0)1381 622488 Fax: 0845 280 2225 Email:

Copyright Highland Horn Company Ltd. © 2019   |   Terms & Conditions   |   Website by plexus media